QUESTIONS?As a manufacturer, we are com-mitted to providing completecustomer satisfaction. If youhave questions, or find that thereare missing or dama
1015. See the inset drawing. Attach the MilitaryPress Arm (84) to the Pivot Arm (101) withtwo 5/16” x 2 1/4” Bolts (33) and two 5/16”Nylon Locknuts (3
1117. Attach the Left Pull-up Arm (75) and the RightPull-up Arm (77) to the Assist Upright (74)with two 5/16” x 2 3/4” Bolts (11) and two5/16” Nylon L
1220. Wrap the High Cable (58) around a “V”-Pulley(50). Attach the “V”-Pulley and a Long CableTrap (31) to the indicated bracket on the FrontUpright (
1324. See the inset drawing. Attach a 3 1/2” Pulley(15) and a Cable Trap (66) to the upper hole ina Long “U”-Bracket (57) with a 3/8” x 2” Bolt(12) an
1427. Locate the Low Cable (23). Route the LowCable under the 3 1/2” Low Pulley (102). Besure that the end of the Cable with the ballis on the indicat
1531. Attach the end of the Low Cable (23) to theLong “U”-Bracket (57) with a 1/4” NylonLocknut (2) and a 1/4” Flat Washer (10). Donot completely tigh
1634. Wrap the Military Press Cable (72) around a“V”-Pulley (50). Attach the “V”-Pulley to theTop Frame (55) with a 3/8” x 2 1/2” Bolt (86)and a 3/8”
1736. Slide a 5/16” Flat Washer (8) onto a 5/16” x2 3/4” Bolt (11). Insert the Bolt through the indi-cated hole in the Pivot Arm (101). The Boltmust b
1838. Locate the Leg Press Cable (99). Attach theend of the Leg Press Cable to the Long “U”-Bracket (57) with a 1/4” Nylon Locknut (2) anda 1/4” Flat
1940. Locate and open the parts bag labeled“SEAT ASSEMBLY.”Insert a 1/4” x 2 1/2” Carriage Bolt (92)through the center hole in a Seat Plate (37).Attac
1. Read all instructions in this manual and inthe accompanying literature before using theweight system. 2. It is the responsibility of the owner to e
2043. Attach the Front Backrest (41) to the FrontUpright (42) with two 1/4” x 2 1/2” Screws (43)and two 1/4” Flat Washers (10). The Backrestmust be or
47. Press two 3/4” Round Inner Caps (34) intoeach Pad Tube (28). Insert a Pad Tube (28) into the Front SeatFrame (36). Slide a Foam Pad (30) onto each
22HOW TO USE THE WEIGHT SYSTEMThe instructions below describe how each part of the weight system can be adjusted. Refer to the exerciseposter accompan
23ATTACHING AND REMOVING THE SEATTo attach the Seat (13), set the bracket on the FrontSeat Frame (36) onto the indicated pins on the FrontUpright (42)
24WEIGHT RESISTANCE CHARTThis chart shows the approximate weight resistance at each weight station. “Top” refers to the 6.5 lb. top weight.The other n
TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the weight system. Replace any worn parts immediately. Theweight syst
26CABLE DIAGRAMSThe cable diagrams on these pages show the proper routing of the High Cable (58), the Low Cable (23), theMilitary Press Cable (72), an
27Military Press Cable (72)Leg Press Cable (99)Rear Weight Stack—1234765324—Rear Seat Frame8—Pivot Arm1—Long “U”-BracketMilitary Press Cable (72) and
5/16" Nylon Locknut (3)1/4" Flat Washer (10)5/16" Flat Washer (8)3/8" Flat Washer (9)1/4" x 2 1/2" Screw (43)3/8" N
1" Retainer (69)3/8" x 3 1/2" Bolt (16)1/4" x 3/4" Screw (18)5/16" x 5" Bolt (68)3/8" x 3 3/4" Bolt (88)3
3BEFORE YOU BEGINASSEMBLED DIMENSIONS: Height: 78 in.Width: 110 in. Length: 92 in. Foot PlateHigh Pulley StationLat BarLeg LeverButterfly ArmsAssist A
1" Round Inner Cap (49)1" Round Cover Cap (70)3/4" Round Inner Cap (34)1/2" x 3/4" Spacer (61)5/16" x 2" Eyebolt (3
PART LIST—Model No. WESY49310 R1101ANote: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Key No. Qty. Desc
602721505586118151244881558214421361622435871265108642526199334962246461639152159232117271410434142213503186706969702147444544454850318613403837183234
ORDERING REPLACEMENT PARTSTo order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Mondaythrough Friday, 6
4ASSEMBLY1811512714315151. Before beginning assembly, be sure thatyou have read and understand the infor-mation in the box above.Locate and open the p
52. Slide the Assist Upright (74) and the LegPress Upright (56) onto the indicated 5/16” x2 1/2” Carriage Bolts (1) in the Stabilizer (5).The high sid
64. Press a 2” Square Inner Cap (27) into the endof the Top Frame (55). Press a 1 3/4” SquareInner Cap (44) into each end of the crossbaron the Top Fr
77. Press a Weight Tube Bumper (64) into theend of the Short Weight Tube (108). Insert theWeight Tube into the front stack of Weights(25). Be sure tha
89. Attach the upper ends of the Short WeightGuides (73) to the Top Frame (55) with a 5/16”x 6” Bolt (60), two 1/2” x 3/4” Spacers (61), anda 5/16” Ny
912. Press a 1” Round Inner Cap (49) into one ofthe Press Arms (46). Press a 1 3/4” SquareInner Cap (44) into the Press Arm.Attach the Press Arm (46)
Komentarze do niniejszej Instrukcji