USER'S MANUALQUESTIONS?As a manufacturer, we are committed to providing completecustomer satisfaction. If youhave questions, or if there aremissi
1015484810842810284848535315. Insert a 2” Square Inner Cap (28) into the end ofthe Butterfly Arm (10).Attach a Butterfly Handle (53) to the Butterfly
21.Locate and open the parts bags labeled “CABLEASSEMBLY” and “PULLEYS.”Secure a 3/8” x 2 1/4” Bolt (79) to the Right PivotArm (85) with a 3/8” Nylon
1223. Remove the preassembled 3/8” x 2” Bolts (54) fromone set of Adjustable Pulley Plates (23).Wrap the Butterfly Cable (73) around a 3 1/2”Pulley (2
1327. Wrap the Ab Cable (47) around a 3 1/2” Pulley (24).Insert the Ab Cable down through the Press TopFrame (9). Attach a 3/8” Flat Washer (48) and a
1431. Locate the Weight Cable (72). Note that one endof the Weight Cable has a bolt, and the otherend has a ball on it. Lay the Weight Cable (72) insi
1536373835. Wrap the Weight Cable (72) around a 3 1/2” Pulley(24). Attach the 3 1/2” Pulley and a Cable Trap (25)to the Butterfly Upright (1) with a 3
1639. Wrap the Weight Cable (72) around a 3 1/2” Pulley(24). Attach the 3 1/2” Pulley and a Cable Trap (25)between the lowest holes in the Adjustable
1743. Locate the Leg Press Cable (75). Attach the LegPress Cable to the indicated side of the PressUpright (2) with a 3/8” x 3 1/4” Bolt (62) and a 3/
1847. Remove the 3/8” Nylon Locknut (50) from the indi-cated 3/8” x 5 1/2” Bolt (55). Wrap the Leg Press Cable (75) around a 3 1/2”Pulley (24). Secure
1951. Locate and open the parts bag labeled “SEATASSEMBLY.”Attach a Seat (13) to the brackets on the ButterflySeat Frame (14) using four 1/4” x 3/4” B
2TABLE OF CONTENTSLIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before using the training system, pull each cable a few times to be sure that the cables move smoothly overthe pulleys. If one of the cables does not
21HOW TO USE THE TRAINING SYSTEMThe instructions below describe how each part of the training system can be adjusted. Refer to the exerciseguide accom
22ATTACHING THE AB STRAP TO THE AB PULLEYSTATIONAttach the Ab Strap (81) to the Ab Cable (47) at the abpulley station with a Cable Clip (69). ADJUSTIN
23WEIGHT RESISTANCE CHARTThis chart shows the approximate weight resistance at each weight station. “Top” refers to the 10 lb. top weight.The other nu
TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the training system. Replace any worn parts immediately. Thetraining
25CABLE DIAGRAMSThe cable diagrams on this page and the next page show the proper routing of the Leg Press Cable (75), the AbCable (47), the Butterfly
26Weight Cable (72)231—Low Pulley481112—WeightStack765Cable ID72 47 75 73910
3/4" Round Inner Cap (43)Cable Clip (69)"V" Pulley (27)(Not shown to scale)3 1/2" Pulley (24)(Not shown to scale)Retainer Ring (31
3/8" x 1" Bolt (84)3/8" x 1 3/4" Bolt (57)3/8" x 1 1/4" Button Head Bolt (98)1/4" x 3/4" Bolt (49)3/8" x
2" x 3” Inner Cap (78)2" Square Inner Cap (28)1 1/2" Square Inner Cap (35)1 1/2" x 2 1/2” Inner Cap (83)2 1/2" Square Inner C
IMPORTANT PRECAUTIONS31. It is the responsibility of the owner to ensurethat all users of the training system are ade-quately informed of all precauti
PART LIST—Model No. WESY59100 R1200ANote: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Key No. Qty. Desc
929249394923252425242350542325242524235044354986657728658677642524609668362524508682936683663252425246090786248508040205083 66024255050495024255075050
ORDERING REPLACEMENT PARTSTo order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Mondaythrough Friday, 6
4BEFORE YOU BEGINASSEMBLED DIMENSIONS: Height: 76.0 in.Width: 86.5 in. Length: 91.5 in. Foot PlateLow PulleyStationHigh Pulley StationLat BarLeg Lever
5ASSEMBLYMake sure you have the following tools:• Two (2) adjustable wrenches• One (1) standard screwdriver• One (1) phillips screwdriver• One (1)
1.Locate and open the parts bags labeled “FRAMEASSEMBLY.”See the inset drawing. Insert two 1 1/2” x 2 1/2”Inner Caps (83) and two 3/8” x 2” Carriage B
5. Attach the Butterfly Seat Frame (14) to the ButterflyUpright (1) with two 3/8” x 3 1/4” Bolts (62), two 3/8”Flat Washers (48), and two 3/8” Nylon L
88948484889516504821Slot159. See the inset drawing. Insert two Weight Inserts(56) into each Weight (21).Set the two Weight Bumpers (51) over the holes
94862504833912. Secure the Press Top Frame (9) to the Butterfly TopFrame (33) with two 3/8” x 3 1/4” Bolts (62), two3/8” Flat Washers (48), and two 3/
Komentarze do niniejszej Instrukcji