Weider 831.159833 Instrukcja Użytkownika

CAUTIONRead all precautions and instruc-tions in this manual before usingthis equipment. Save this manu-al for future reference.WEIGHT SYSTEM EXERCISE

1013. Slide six Weights (41) onto the Right WeightGuides (26). Make sure the Weights are turnedso the pin grooves are on the bottom.Press a Weight Tub

11105922928 67 89090902627475892857792351516382910590909015. Press a 50mm Square Inner Cap (67) into theCenter Top Frame (8). Place the Center TopFr

1220. See the inset drawing. Press a Plastic Bushing(60) onto each welded tube on the Press Frame(17). Slide the Press Frame into place on thePress Ba

132386208473Bracket2441149073373422. Identify the Right and Left Butterfly Arms (19, 20)by the positions of the welded brackets.Press a 45mm Square In

1426. Remove another “V”-pulley (34) from the baglabeled “PULLEY BAG 2.”Wrap the Butterfly Cable (73) over the “V”-pulley(34). Attach the “V”-pulley a

32. Identify the Ab Cable (74). It is approximately226 1/2” long, and it has a ball on one end andan eyelet on the other.Wrap the Ab Cable (74) over a

1634. Wrap the Ab Cable (74) over a 90mm Pulley (35)in the direction shown. Attach the Pulley to theDouble “U”-bracket (31) with an M10 x 45mm Bolt(94

1738933274353838. Wrap the Ab Cable (74) over a 90mm Pulley (35)in the direction shown. Attach the Pulley and aCable Trap (38) to the second set of ho

1841. Locate the Weight Plate (48) that is attachedto the bottom of the Bottom Weight (47).See the inset drawing. Attach the end of the AbCable (74) t

1945. Remove the M10 Nylon Locknut (90) used instep 43.Wrap the Low Cable (71) under a 90mm Pulley(35). Attach the Pulley and a Cable Trap (38) tothe

2TABLE OF CONTENTSIMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2049. Wrap the Press Cable (72) under a 90mm Pulley(35). Attach the Pulley and a Cable Trap (38) tothe indicated hole in the Press Upright (5) with an

2153. Wrap the Press Cable (72) around a 90mmPulley (35) in the direction shown. Attach thePulley and a Cable Trap (38) to the indicated holeon the ri

2257. Remove the M10 Nylon Locknut (90) used instep 53. Route the Press Cable (72) through the PressFrame (17).Wrap the Press Cable (72) under a 90mm

2361. Attach the Press Cable (72) to the remaining “U”-bracket (33) with an M8 Washer (100) and an M8Nylon Locknut (86). Note: Do not completelytighte

2465. Press a 45mm Square Inner Cap (68) into theindicated end of the Adjustment Tube (15).Orient the Leg Press Plate (16) and AdjustmentTube (15) as

25ADJUSTING THE LEG PRESS PLATETo adjust the position of the Leg Press Plate (16), pullout the Adjustment Pin (40) and slide the AdjustmentTube (15)

2681474141CHANGING THE WEIGHT SETTINGTo change the setting of a weight stack, insert aWeight Pin (81) under the desired Weight (41). Insertthe Weight

27WEIGHT RESISTANCE CHARTThe chart below shows the approximate weight resistance at each exercise station. “Left Top” and “Right Top”refer to the 6 lb

28The threaded ends on the Rear Cable (70) and thePress Cable (72) attached to the weight stacks canbe used to tighten the cables. To tighten the Rea

299712729234909757285345903737Slack can be removed from the Press Cable (72) bymoving the “V”-pulley (34) attached to the Press SeatFrame (12) closer

3IMPORTANT PRECAUTIONSWARNING: To reduce the risk of serious injury, read the following important precautionsbefore using the weight system.1. Read al

CABLE DIAGRAMSThe Cable Diagrams below and on the next page show the proper routing of the Rear Cable (70), the Low Cable(71), the Press Cable (72), t

Low Cable (71)54312673189101156214124323Butterfly Cable (73)5Rear Cable (70)314Ab Cable (74)

M10 x 63mm Carriage Bolt (76)M6 x 65mm Bolt (79)M4 x 25mm Screw (80)M10 x 67mm Bolt (82)M10 Nylon Locknut (90)M8 Nylon Locknut (86)M6 Nylon Locknut (1

M10 x 97mm Bolt (77)M10 x 93mm Bolt (85)M10 x 76mm Bolt (88)M6 x 62mm Carriage Bolt (91)M10 x 91mm Bolt (101)M10 x 121mm Bolt (102)M10 x 72mm Bolt (10

25mm Retainer (54)25mm Round Cover Cap (55)25mm Round Inner Cap (66)19mm Round Inner Cap (64)50mm Square Inner Cap (67)45mm Square Inner Cap (68)25mm

Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. 11Butterfly Base21Center Base31Press Base41Butterfly

625962625635383835353835353837341818603538383232231234373838383814403535616110950151647414127462646424445333517935293835109323238353538363628288343437

Part No. 202725 R1203A Printed in China © 2003 Sears, Roebuck and Co.FULL 90-DAY WARRANTYFor 90 days from the date of purchase, if failure occurs due

4ASSEMBLED DIMENSIONS: Height: 77 in.Width: 80 in. Depth: 59 in. Low PulleyStationFoot PlateLeg LeverPress ArmBackrestCurl PadButterfly ArmAb PulleySt

5ASSEMBLYMake sure that you have the following tools:• Two adjustable wrenches• One standard screwdriver• One phillips screwdriver• One rubber mal

1. Before beginning, be sure that you have readand understood the information on page 5.Locate and open the parts bag labeled“FRAME ASSEMBLY.”Press a

4. Slide the Butterfly Upright (4) over the indicatedM8 x 61mm Carriage Bolts (75) in the ButterflyBase (1). Hand tighten two M8 Nylon Locknuts(86) on

78. Press a 25mm Square Inner Cap (69) into thesmall tube on the Press Upright (5).Slide the Press Upright (5) over the indicated M8x 61mm Carriage B

910. Press a 50mm Square Inner Cap (67) into thePress Top Frame (9). Attach the Press Top Frame (9) to the indicatedbracket at the top of the Press Up