Weider 8510 Instrukcja Użytkownika

USER'S MANUALQUESTIONS?As a manufacturer, we are com-mitted to providing completecustomer satisfaction. If you havequestions, or find there are m

1015. Route the Long Cable (23) around the ÒVÓ-Pulley (6) on the Right Arm (48). Be surethat the Cable is in the groove of the ÒVÓ-Pulley and that the

11CABLE ASSEMBLY19. Note: This assembly step shows how tocomplete the assembly of several pre-attached parts.The 5/8Ó x 9/16Ó Spacer (73) has been pre

1221. Route the Short Cable (58) around the 3 1/2ÓPulley (15) attached to the lower hole in theFront Upright (42). See the inset drawing.Be sure that

24. Attach the end of the Short Cable (58) to theLong ÒUÓ-Bracket (57) with a 1/4Ó Nylon Lock-nut (2) and a 1/4Ó Flat Washer (10). Do notcompletely ti

1426. Attach the Backrest (41) to the Front Upright(42) with two 1/4Ó x 2 1/2Ó Screws (43) andtwo 1/4Ó Flat Washers (10).27. Press a 1 1/2Ó Square Inn

1529. Rest the Seat Frame (36) on the indicated pinin the Front Upright (42). Attach the SeatFrame to the Front Upright with a 5/16Ó x2 3/4Ó Carriage

1631. Remove the decals from the decal sheet (not shown) and apply them to the home gym system in the loca-tions shown below.HIGH PULLEYBUTTERFLY8510B

17ADJUSTMENTThe instructions below describe how each part of the home gym system can be adjusted. Refer to the exerciseposter accompanying this manual

18ATTACHING AND REMOVING THE SEATSet the bracket on the Seat Frame (36) onto the indi-cated pins on the Front Upright (42). Attach the SeatFrame to th

19TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the home gym system. Replace any worn parts immediately. Thehome gy

2TABLE OF CONTENTSLIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20CABLE DIAGRAMThe cable diagram below shows the proper routing of the Short Cable (58) and the Long Cable (23). Use thediagram to be sure that the tw

21NOTES

22Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. PART LISTÑModel No. WESY85101 R1196AKey No. Qty. De

231111885527121544157123272144213616035615122575821355114192651256463769213341276515714110433216507427506216970697047484445444513403837183228303410224

1Ó Round Inner Cap (49)Ð61Ó Round Cover Cap (70)Ð23/4Ó Round Inner Cap (34)Ð41/2Ó x 3/4Ó Spacer (61)Ñ25/16Ó x 2Ó Eyebolt (35)Ñ11 1/2Ó Square Inner Cap

1" Retainer (69)Ð43/8" x 2" Bolt (12)Ð33/8" x 3 1/2" Bolt (16)Ð13/8" x 2 1/2" Bolt (7)Ð33/8" x 3 3/4" Bo

5/16" Nylon Locknut (3)Ð171/4" Flat Washer (10)Ð65/16" Flat Washer (8)Ð53/8" Flat Washer (9)Ð41/4" x 2 1/2" Screw (43)Ð2

ORDERING REPLACEMENT PARTSTo order replacement parts, simply call our Customer Service Department toll-free at 1-800-225-0653, Mondaythrough Friday, 6

31. It is the responsibility of the owner to ensurethat all users of the home gym system areadequately informed of all precautions.2. Read all instruc

4BEFORE YOU BEGINASSEMBLED DIMENSIONS: Height: 76 in.Width: 38 in. Length: 53 in. Foot PlateLow Pulley StationHigh Pulley StationLat BarLeg LeverButte

5ASSEMBLY156High Side ofBracket355151141274Before beginning assembly, carefully read thefollowing information and instructions:¥ Place all parts of th

6FRAME ASSEMBLY2. Slide the Front Upright (42) onto the 5/16Ó x2 1/2Ó Carriage Bolts (1) in the Base (4).Hand tighten a 5/16Ó Nylon Locknut (3) ontoea

7FRAME ASSEMBLYARM ASSEMBLY5. Press the Weight Tube Bumper (64) into theend of the Weight Tube (63). Insert theWeight Tube into the stack of Weights (

8ARM ASSEMBLY8. Press a 1 3/4Ó Square Inner Cap (44) into thetop of a Press Arm (46). Press a 1Ó RoundInner Cap (49) into each end of the handle onthe

9CABLE ASSEMBLY11. During steps 11 through 25, refer to theCABLE DIAGRAM on page 20 of this manualto verify proper cable routing. Before begin-ning th