Weider 8530 Instrukcja Użytkownika

USERÕS MANUALQUESTIONS?As a manufacturer, we are com-mitted to providing completecustomer satisfaction. If you havequestions, or find that there aremi

1017. Route the Medium Cable (58) around the3 1/2Ó Pulley (15) attached to the bracket onthe Top Frame (55). Tighten the 3/8Ó x 2Ó Bolt(12) and the 3/

1121. Attach the Medium Cable (58) to a Small ÒUÓ-Bracket (71) with a 1/4Ó Nylon Locknut (2)and a 1/4Ó Flat Washer (10). Do not tightenthe 1/4Ó Nylon

1223. Route the Long Cable (72) around the 3 1/2ÓPulley (15) on the Top Frame (55). Tightenthe 3/8Ó Nylon Locknut (21) and the 3/8Ó x 2ÓBolt (not show

1325. See inset drawing A. Note: The inset draw-ing shows the view from the other side ofthe Squat Arm Upright (56). Wrap the LongCable (72) around a

1428. Press a 1 1/2Ó Inner Cap (32) into the LegLever (29).Lubricate the 5/16Ó x 2 1/4Ó Bolt (33). Attachthe Leg Lever (29) to the Seat Frame (36)with

32. Wet the handle on the Right VKR Arm (80)with soapy water. Slide a 5Ó Plastic Grip (83)onto the Handle. Press a 1Ó Round Inner Cap(49) into the bot

16HOW TO USE THE HOME GYM SYSTEMThe instructions below describe how each part of the home gym system can be adjusted. Refer to the exerciseposter acco

17ATTACHING AND REMOVING THE SEATTo attach the Seat (13), set the bracket on the SeatFrame (36) onto the indicated pins on the FrontUpright (42). Atta

TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the home gym system. Replace any worn parts immediately. Thehome gym

19CABLE DIAGRAMThe cable diagram below shows the proper routing of the Long Cable (72), the Medium Cable (58), and theShort Cable (23). Use the diagra

2IMPORTANT PRECAUTIONSWARNING: To reduce the risk of serious injury, read the following important precautions beforeusing the home gym system.1. Read

PART LISTÑModel No. WESY85301 R0100ANote: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. Key No. Qty. Desc

683202115661227837880757510817732837879310437411113511127195121525642612661563652427172367315076215654838352533921939215948438822498283878522883828387

1" Retainer (69)Ð43/8" x 3 1/2" Bolt (16)Ð11/4" x 3/4" Screw (18)Ð25/16" x 5" Bolt (68)Ð13/8" x 3 3/4" B

1" Round Inner Cap (49)Ð61" Round Cover Cap (70)Ð23/4" Round Inner Cap (34)Ð41/2" x 3/4" Spacer (61)Ð45/16" x 2" Ey

5/16" Nylon Locknut (3)Ð271/4" Flat Washer (10)Ð135/16" Flat Washer (8)Ð73/8" Flat Washer (9)Ð41/4" x 2 1/2" Screw (43)Ð

ORDERING REPLACEMENT PARTSTo order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Mondaythrough Friday, 6

3BEFORE YOU BEGINASSEMBLED DIMENSIONS: Height: 74 in.Width: 60 in. Length: 54 in. Foot PlateLow Pulley StationHigh Pulley StationLat BarLeg LeverButte

4ASSEMBLY1745633811512714315127HighSide51. Before beginning assembly, be sure thatyou have read and understand the infor-mation in the box above.Press

42352. Insert two 5/16Ó x 2 1/2Ó Carriage Bolts (1) upthrough the Base (4).Slide the Front Upright (42) onto the 5/16Ó x2 1/2Ó Carriage Bolts (1) in t

5665. Press a Weight Tube Bumper (64) into theend of a Weight Tube (63). Insert the WeightTube into the front stack of Weights (25). Besure that the p

7. Attach the upper ends of the Long WeightGuides (62) to the Top Frame (55) with a5/16Ó x 6Ó Bolt (60), two 1/2Ó x 3/4Ó Spacers(61), and a 5/16Ó Nylo

811. Lubricate both axles on the Top Frame (55). Slide the Right Arm (48) onto the right axle.Be careful not to confuse the Right Armwith the Left Arm

9During steps 13 to 25, refer to the CABLE DIA-GRAM on page 19 of this manual. Identify thethree cables by their lengths, and note thepositions of the