Weider WESY93190 Instrukcja Użytkownika

USERÕS MANUAL9925QUESTIONS?As a manufacturer, we are committed to providing completecustomer satisfaction. If youhave questions, or if there aremissin

17. Attach a Press Arm (7) to one side of the PressFrame (12) with two 5/16Ó x 2 1/2Ó Bolts (39) and two5/16Ó Nylon Locknuts (40).Attach the other Pre

20. Press a 1 3/4Ó Square Inner Cap (48) into the lowerend of the Left Arm (6) and the Right Arm (5).21. Locate and open the parts bags labeled ÒCABLE

23. Wrap the Butterfly Cable (89) around a 3 1/2Ó Pulley(82) as shown. Attach the Pulley and two PulleyCovers (94) to the bracket on theLeg Press Upri

27. Locate the Rear Cable (87)Ñthis is the shortestCable. Slide one end of the Rear Cable onto the5/16Ó x 3Ó Bolt (92). Thread another 5/16Ó Nylon Jam

31. Locate the Press Cable (88)Ñthis is the longestCable. Attach the end of the Press Cable (88) to theLarge ÒUÓ Bracket (84) with a 1/4Ó Nylon Locknu

34. Wrap the Press Cable (88) around a 3 1/2Ó Pulley(82) in the direction shown. Attach the Pulley and twoPulley Covers (94) to the lower set of holes

38. Wrap the Press Cable (88) around a 3 1/2Ó Pulley(82) in the direction shown. Attach the Pulley and twoPulley Covers (94) to the indicated hole in

42. Remove the 3/8Ó Nylon Locknut (42) from the3/8Ó x 5Ó Bolt (74) attached in step 40. Wrap thePress Cable (88) around a 3 1/2Ó Pulley (82) in thedir

46. Locate one of the preassembled pairs of PulleyPlates (31) and remove both 3 1/2Ó Pulleys (82).Route the High Cable (85) around a 3 1/2Ó Pulley (82

50. Wrap the Low Cable (86) around a 3 1/2Ó Pulley (82)in the direction shown. Attach the Pulley and twoPulley Covers (94) to the welded tube on the A

2IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2BEFO

56. Locate and open the parts bag labeled ÒSEATASSEMBLY.ÓAttach the Small Backrest (18) to the Ab Upright (1)with two 1/4Ó x 2 1/2Ó Machine Screws (64

58. Press two 3/4Ó Round Inner Caps (78) into each PadTube (28). Insert a Pad Tube (28) into the Rear Seat Frame (16).Slide a Foam Pad (29) onto each

61. Attach a Butterfly Pad (22) to the Left Fly Arm (6) withtwo 1/4Ó x 2Ó Machine Screws (63).Repeat this step for the Right Fly Arm (5).61CHANGING TH

ATTACHING THE AB STRAP TO THE AB PULLEYSTATIONAttach the Lat Bar (36) to the Low Cable (86) at the abpulley station with a Cable Clip (33). ADJUSTING

24This chart shows the approximate weight resistance at each weight station. ÒTopÓ refers to the 6.5 lb. top weight.The other numbers refer to the 12.

Inspect and tighten all parts each time you use the home gym system. Replace any worn parts immediately. Thehome gym system can be cleaned using a dam

26The cable diagrams on this page and the next page show the proper routing of the High Cable (85), the LowCable (86), the Rear Cable (87), the Press

27High Cable (85) Rear Cable (87)Weight StackÑ5High PulleyÑ122331ÑTop Frame4ÑWeight Stack4

1/2" x 3/4" Spacer (69)2" Square Inner Cap (56)2" Square Outer Cap (58)1 3/4" Square Inner Cap (48)1" Round Outer Cap (4

3/8" Nylon Jam Nut (43)3/8" x 2" Bolt (50)5/16" x 2 1/4" Bolt (62)5/16" x 2 1/2" Bolt (39)3/8" x 2 1/2"

3ASSEMBLED DIMENSIONS: Height: 78 in.Width: 64 in. Length: 70 in. Foot PlateLow PulleyStationHigh Pulley StationLat BarLeg LeverButterfly ArmsPress Ar

5/16" x 2" Eyebolt (79)Cable Clip (33)3/8" x 5" Bolt (74)3/8" x 3 3/4" Bolt (76)5/16" x 2 1/2" Carriage Bolt (

Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. Part ListÑModel No. WESY93190

294056725376829494387642857643769438829474423894829438829468983268329882949482949431993194948294948236212194384282943882421234567789101112131416171819

To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Mondaythrough Friday, 6 a.m. until 6 p.m. Mountai

4Note: This introduction will save you moretime than it takes to read it!Identifying PartsTo help you identify the small parts used in assem-bly, we h

1. Before beginning assembly, be sure that you haveread and understand the information in the boxabove.Locate and open the parts bags labeled ÒFRAMEAS

4. Slide the Front Seat Frame (8) onto the indicated5/16Ó x 2 1/2Ó Carriage Bolts (49) in the Press Base(13). Hand tighten two 5/16Ó Nylon Locknuts (4

8. Slide a Weight Bumper (27) onto each of the WeightGuides (23).Slide eight Weights (90) onto each set of WeightGuides (23). Make sure the pin groove

10. Lubricate the insides of the holes in the Top Weights(24) as shown. Slide a Top Weight onto each set ofWeight Guides (23).11. Attach the Top Frame

13. Attach the Leg Press Plate (11) to the AdjustmentTube (10) with a 5/16Ó x 2 1/2Ó Bolt (39), two 5/16ÓWashers (20) and a 5/16Ó Nylon Locknut (40).